1939 - 1947 Dodge Truck Steel GasTank for EFI -Tank, 400 lph Pump & Sending Unit

Description: Here we have a new, galvanized steel fuel tank, fuel pump and fuel level sending unit for 1939 - 1947 Dodge Pick-up Trucks ( it has been brought to my attention by customers that they have used this tank in 48-53 Dodge trucks also with a little fitting. See notes at bottom of this page.) Our part number is 39DP-T Combo They are built by Tanks Inc. and measure 38 3/4" x 12 1/4" x 12 1/2" 18 gallon capacity. This tank has a 3/8" npt female fuel pick-up in the stock location. The GPA-6 Walbro In-tank fuel pump assembly is rated for 400 lph and up to 900 hp @ 60 psi. This is the preferred pump for fuel injection based swaps. The assembly has the pressure port, the return port and a vent port. (They are 1/4" npt female) The TAN-ORG 73-10 ohm fuel level sending unit included is for the stock gauge. Works with either 6 or 12 volt Most tanks are in stock and will normally ship within 1-2 business days. Check our other auctions for more fuel tanks, steering, frame and suspension parts . If you have any questions please ask through eBay Messages. Here is why you cannot find my phone number listed on Ebay anymore........ Buyers and sellers should always use eBay messaging tools (My Messages, Best Offer) to communicate with one another. By September 2017, sellers will no longer be allowed to include contact information, such as email, phone numbers, and social media links, in item descriptions, titles, or other eBay pages. Will combine shipping when feasible. Shipping to the lower 48 states only. No overseas shipping. Modifications for the 39-47 Dodge Truck tank to work in the 1948-53 Dodge trucks The 1939-47 Dodge tank is shorter than the 1948-53 Dodge Truck tanks. Also, the neck is at a slightly different angle. The newer trucks used a tank that was 3.5 inches longer than the 39-47 Tanks, Therefore, it requires a bracket at the end of the tank, to the rear, to be constructed to support that end of the shorter tank. A similar bracket was used in the 39-47 Dodge trucks, that had a longer wheelbase than the 116” of the half ton trucks. Example is the 120” and 133” trucks. To use the shorter tank in the B Series trucks. It requires a triangle shaped bracket, one side bolted to the frame side (two bolts) and the bottom of frame (one bolt), and the bottom of the triangle would be bolted to the holes in the flange of the gas tank. As for the front end, the bolt holes on the tank flange line up perfectly with the cross member mounting holes, just the same as the 39-47 trucks, and the angled filler neck lines up with the hole in cab floor. However, it is a slightly different angle and some simple modifications must be made. The hole in floor should be enlarged about 1 inch on left side to allow connection to filler tube. That tube is longer and has a crook in it that should be removed. (inlet on side of cab is lower on the body) So, simply cutting off the bottom 5 inches of the steel filler neck and using a longer rubber hose connection will allow good fit. Use about 10” of hose instead of the 5 inches. Tank fits well on the top, and on both sides there is clearance, basically the same as the 39-47 Dodge trucks. Attention California Residents:WARNING: This store sells products that may contain chemicals which are known to the State of California to cause cancer, birth defects, or other reproductive harm. By ordering products for delivery into California, you acknowledge that you have received this warning. Please feel free to contact us should you have any questions. For more information, go to www.P65Warnings.ca.gov. Concerning Returns – Buyer is responsible for return shipping – 10% will be deducted from refund to cover fees

Price: 634.99 USD

Location: Missouri Ozarks

End Time: 2024-12-05T18:29:11.000Z

Shipping Cost: 0 USD