CB Radio Generic Mobile Transceiver RFI/Noise Reduction Kit, RFI Range: 20-60 MH

Description: CB Radio Generic Mobile Transceiver RFI/Noise Reduction Kit, RFI Range: 20-60 MHz, Works on all brands Palomar Engineers RFI Filter Kit for CB Radio Radio Transceivers from 20-30 MHz uses ferrite rings for the DC power supply and the coax to the antenna. BUY THIS KIT NOW TO SOLVE YOUR RFI/EMI NEEDS! WORKS WITH ALL BRANDS (Cobra, DAS, Midland, Uniden etc.) OF CB/HAM/COMMERCIAL RADIO RIGS in 20-60 MHz range.PurposeThe RFI kit is designed to be installed on your radio transceiver to reduce Radio Frequency Interference (RFI) caused by common mode current on the outside of the coax braid at the output of your radio and on the DC power supply cable. This kit will help reduce or eliminate:1. “Hot mic” RFI caused by poor grounding of antennas or common mode currents from linear amps feeding unbalanced (coax fed) antennas without baluns/line isolators.2. RFI to neighbor’s electronic devices including audio/video systems, computers, telephones, garage door openers, etc.3. RFI to your other radios, audio/video systems, computers, telephones, etc.A side benefit is a reduction in noise floor in your receiver depending on the amount of noise being introduced by common mode currents (which are blocked/reduced by the chokes in this kit). These chokes use a special mix of ferrite core material that is effective in suppressing radio frequency interference from Ham Radio amplifiers. Included are the following chokes and installation guidelines:DC Input: F240 Ring – 3-7 turns of DC power cable - sized for smaller plugsRF Input/Output: F240-31 ring - wrap 6 turns of RG8X size cable near the back of the radioAlso make sure you connect a good RF ground to the transceiver ground post.For additional RFI suppression, use a MC-1-500-50 mini feed line choke at the antenna feed point to suppress common current on the coax feed line during transmit and a CMNF-500-50 Coax Noise Filter to reduce common mode noise during receive operations.If you use a switching power supply for base operation, consider the RFI-SMPS switching power supply RFI kit.If you use a linear amplifier we have RFI kits for linear amplifiers that help suppress RFI in your shack or in your neighbor’s house. CB Radio Generic Mobile Transceiver RFI/Noise Reduction Kit, RFI Range: 20-60 MHz, Works on all brands Palomar Engineers RFI Filter Kit for CB Radio Radio Transceivers from 20-30 MHz uses ferrite rings for the DC power supply and the coax to the antenna. BUY THIS KIT NOW TO SOLVE YOUR RFI/EMI NEEDS! WORKS WITH ALL BRANDS (Cobra, DAS, Midland, Uniden etc.) OF CB/HAM/COMMERCIAL RADIO RIGS in 20-60 MHz range. Purpose The RFI kit is designed to be installed on your radio transceiver to reduce Radio Frequency Interference (RFI) causéd by common mode current on the outside of the coax braid at the output of your radio and on the DC power supply cable. This kit will help reduce or eliminate: 1. “Hot mic” RFI causéd by poor grounding of antennas or common mode currents from linear amps feeding unbalanced (coax fed) antennas without baluns/line isolators. 2. RFI to neighbor’s electronic devices including audio/video systems, computers, telephones, garage door openers, etc. 3. RFI to your other radios, audio/video systems, computers, telephones, etc. A side benefit is a reduction in noise floor in your receiver depending on the amount of noise being introduced by common mode currents (which are blocked/reduced by the chokes in this kit). These chokes use a special mix of ferrite core material that is effective in suppressing radio frequency interference from Ham Radio amplifiers. Included are the following chokes and installation guidelines: DC Input: F240 Ring – 3-7 turns of DC power cable - sized for smaller plugs RF Input/Output: F240-31 ring - wrap 6 turns of RG8X size cable near the back of the radio Also make sure you connect a good RF ground to the transceiver ground post. For additional RFI suppression, use a MC-1-500-50 mini feed line choke at the antenna feed point to suppress common current on the coax feed line during transmit and a CMNF-500-50 Coax Noise Filter to reduce common mode noise during receive operations. If you use a switching power supply for base operation, consider the RFI-SMPS switching power supply RFI kit. If you use a linear amplifier we have RFI kits for linear amplifiers that help suppress RFI in your shack or in your neighbor’s house. × Buy now and save! Tell a friend Visit store Watch now Postage info Click the Postage tab above the listing description for more info Click the Postage tab above the listing description for more info! Additional delivery notes PICK UP OPTION Sorry, our items are NOT available for pick-up. PAYING VIA PAYPAL We accept PayPal on our all our items so you can shop with confidence. Simple choose the PayPal option when proceeding through the checkout. Additional Information No additional information at this time Ask seller a question Contact To contact our Customer Service Team, simply click the button here and our Customer Service team will be happy to assist. Ask seller a question © PALOMAR-ENGINEERS.COM Postage Click the Postage tab above the listing description for more info Payment Accepted Payment Methods PayPal Returns Returns are not accepted Buyer will pay for return shipping. Additional Information: All returns will be exchanged for like product or store credit provided they are returned within 30 days with original packaging and all manufactured products are in original shipped condition with unsealed product labels. All cash refunds subject to 15% restocking fee. eBay integration by

Price: 19.95 USD

Location: Oceanside, California

End Time: 2024-03-26T16:25:22.000Z

Shipping Cost: N/A USD